GPS
Antenna Splitters by GPS Networking
Antenna splitters eliminate the need to run several antenna cables from several
antennas on the roof. You can just run one cable and split it, this makes your site
installation easier and less expensive.
Some of the splitters on this page are
amplified. Amplified splitters allow long cable runs after the splitter.
Maximum cable length depends on amplification of the splitter, antenna specifications, and
type of cable used.
|
|
The ALDCBS1X2 GPS
antenna splitter is a one input two output amplified power divider designed specifically
for the GPS L1 & L2 carrier frequencies. One of the output legs is DC-Blocked to
prevent antenna damage, it also has a 200 ohm load to ground to simulate a GPS antenna.
The other output leg is a DC short to power the antenna. All GPS
Networking antenna
splitters are available with N-type, SMA, TNC or BNC connectors. $332.50
The ALDCBS1X4 GPS
antenna splitter is a one input four output amplified power divider designed specifically
for the GPS L1 & L2 carrier frequencies. Three of the output legs are DC-Blocked to
prevent antenna damage, they also have 200 ohm loads to ground to simulate a GPS antenna.
The other output leg is a DC short to power the antenna. All GPS
Networking antenna
splitters are available with N-type, SMA, TNC or BNC connectors. $427.50
The ALDCBS1X8 GPS
antenna splitter is a one input eight output amplified power divider designed specifically
for the GPS L1 & L2 carrier frequencies. Seven of the output legs are DC-Blocked to
prevent antenna damage, they also have 200 ohm loads to ground to simulate a GPS antenna.
The other output leg is a DC short to power the antenna. All GPS
Networking antenna
splitters are available with N-type, SMA, TNC or BNC connectors. $855.00
1X8
Rack-Mount Signal Distribution Unit
Fully rack
mountable 1 X 8 splitter, includes a power source (110v or
220v).
Part # RMALDCBS1X8-N (with N-type connectors) $1425.00 
|
Antenna Splitter Options
- (Part #
prefix)
Network -(N) - This option gives you a splitter that has its own power
source & all output ports are DC-blocked. When you designate the Network option, you
must also designate the antenna voltage to be provided by the splitter power source as
well as the source voltage. Add $100
Hi-Isolation (HI) -
This option gives a splitter that has high isolation (40db) between output ports. When you
designate the Hi-Isolation option, you will not get full amplification (20+db). The
Hi-Isolation option gives you 9db gain on a 1X2, 6db gain on a 1X4, and 3db on a
1X8. Add $100
Weather
Proof (WP) - Joints and connectors are sealed for outside use. Add $100
Because there are
so many variations and options available for GPS splitters, please call
our technical support department to place an order, or e-mail
an antenna splitter specialist if you have additional questions.
|
|
|
Splitter |
Part
#, Price |
|
| 1X2
Splitter, N-Type Connectors, No Amplification |
LDCBS1x2-N,
$237.50 |
 |
| 1X4
Splitter, N-Type Connectors, No Amplification |
LDCBS1x4-N,
$332.50 |
|
|
|
|
| 1X2
Splitter Amplified (20dB), N-Type Connectors |
ALDCBS1x2-N,
$332.50 |
|
| 1X4
Splitter Amplified (20dB), N-Type Connectors |
ALDCBS1x4-N,
$427.50 |
|
| 1X8
Splitter Amplified (20dB), N-Type Connectors |
ALDCBS1x8-N,
$855.00 |
|
| 1X2
Splitter Amplified (20dB), Network Option (110v), N-Type |
NALDCBS1x2-N,
$427.50 |
|
| 1X4
Splitter Amplified (20dB), Network Option (110v), N-Type |
NALDCBS1x4-N,
$522.50 |
|
| 1X8
Splitter Amplified (20dB), Network Option (110v), N-Type |
NALDCBS1x8-N,
$950.00 |
|
Listed
above are some of the more common Splitters we carry. Many other
versions of GPS splitters are available.
Please use the part numbering chart above to enquire about
splitter options. |
|
|
Military
Splitter - This
splitter is a 1 X 3 power divider. The three output legs (J2-J4)
are DC-Blocked to prevent antenna damage. J2 & J3 are TNC
connectors and J4 is a N-type connector, J4 also has 5db of
attenuation inline. This splitter has been built to military
specifications.
|
MIL-NLDCBS1X3,
$1425.00 |
|
|
The
LNFA1X4 is a low noise, filtered, amplified 1X4 GPS antenna
splitter that was originally designed to satisfy AT&T's
Wireless requirements. The device features high selectivity for
protection against the proximity of high power cellular
transmitters, very high output port-to-port isolation and very
low operational current. It also features a "pick and
choose" circuit that selects a DC source from those
available on any of the four RF output ports for powering the
splitter and the GPS antenna system. The outputs that are not
chosen as the power source are switched to a 200 Ohm DC load.
|
LNFA1X4-N,
$565.25 |
|
|
